JH3YKV's Amateur Radio News(2005年アーカイブ)

PSK31のみならず、RTTY、SSTV、CWなどの各種の通信が行える超多機能なソフトであるMixWですが、Ver2.14が1月6日にリリースされているようです。

なお、バージョンアップの内容は、以下の通りのようです。

- extended contest support
- CAT support for JRC, FT857, IC7800, IC756PRO3
- MP3 format support (you must have lame_enc.dll in the MixW folder)
Use to start record in the MP3 format
(extension must be "mp3")
- ProSisTel rotor support
- WinKey basic support
- Added e-mail field to the Cabrillo output.
- OmniRig support added
- Log bar font and vertical size can be changed
- Telnet window improvements. Try one of scripts to connect the DX cluster.
DX Spot Send feature uses telnet window automatically.
- Macro <[> and <]> allow transmitting "<" and ">"
- Receiving sensitivity is improved for some modes
- Controller CBOX 2003 for Pro.Sis.Tel rotators is supported
- "Macros for this contest" item is added in the menu Configure.
It is active ONLY in contest mode.
- Frequencies listed in KnownFqs.dat will be shown at the spectrum bar
with grey marks, see KnownFqs.dat for the format and add your own if needed.
- "Search and pounce" (SP) and "Run" modes of operation are added.
Run mode assumes CQ operation.
"Run" is displayed at the caption in Run mode. Three macros are added
to switch between Run and SO.
We can switch between RUN and SEARCH-AND-POUNCE (SP) modes by
(SP on)
(SP off = RUN)
(switch between SP and RUN)
- New Macros
- is similar to but prints miles instead of km
- does the same as pressing TAB key
- macro allows limit the transmission to nn seconds
- macro is similar to , but allows call changing on the fly.
- is similar to but waits for carrier loss (end or transmission)
- will be called (if defined) when two same calls will be received
- will be called if serial when number is grabbed into the log
- will start record a MPEG3 file instead of
usual PCM WAVE. The presence of lame_enc.dll is required in the MixW
folder (separate download).
- moves the cursor to the field number N (not column),
N=5 : Call
N=9 : Nr Recv
Known bug: It does not work if the macro button is pressed with mouse,
use keyboard instead.

- moves the cursor to the TX window
- macro tells MixW what to do if CR will be pressed while focus
is in the log. It calls macro by default in contest mode (see below).
- macro or does a specific job. It's output depends
of the content of CALL and RX EXCHANGE fields.

S/P mode.
Call Rx exchange Output according macro to edit if needed
-empty -empty ? INTQRL
NEWCALL -empty de UT2UZ INTDE
WKDCALL -empty (nothing)
NEWCALL exchange QSL UR 599 001 INTQSL
(and saves the QSO)

RUN mode.
Call Rx exchange Output according macro to edit if needed
-empty -empty CQ TEST DE UT2UZ INTCQ
NEWCALL -empty CALL GA 599 001 INTGA
WKDCALL -empty CALL QSO b4 QRZ INTQB4
NEWCALL exchange QSL 73 QRZ de UT2UZ INTQRZ
(and saves the QSO)

See default macro definnitions and change them if needed.
Of course, macro can be used not only inside OnCR.

なお、詳しくは上記のリンク先をご覧下さい。

＃$50のシェアウェアですが、お勧めの１本です。筆者(7J3AOZ)も愛用しております（笑）